E3D toolchanger Archieven - Jantec.nl

Is E3D tool changer Z-homing with Voron TAP possible?

J.M.W. Griffioen — Thu, 11 Sep 2025 20:27:54 +0000

HOW DOES IT WORK WITH THE E3D TOOLCHANGER? The system whereby the E3D tool changer determines the Z value of the four tools is fixed in the preset system files. This means that you perform a Z homing paper test for each tool to determine the deviation of each tool relative to T0, which is …

Continue reading "Is E3D tool changer Z-homing with Voron TAP possible?"

Het bericht Is E3D tool changer Z-homing with Voron TAP possible? verscheen eerst op Jantec.nl.

E3D toolchanger 4xHemera direct drive first 4-color PLA benchy & 3D-world

J.M.W. Griffioen — Thu, 06 Oct 2022 07:52:57 +0000

The bow of the benchy , the white right part at the bottom sags a bit. The solution was to set the bed temperature at 10 degrees lower. So; I now start with 60 degrees and after the first layer the bed temp goes to 50 degrees. In addition, I flipped the benchy 180 degrees …

Continue reading "E3D toolchanger 4xHemera direct drive first 4-color PLA benchy & 3D-world"

Het bericht E3D toolchanger 4xHemera direct drive first 4-color PLA benchy & 3D-world verscheen eerst op Jantec.nl.

E3D toolchanger: Tuning the tool pickups with reprap global variables and macro’s assistance

J.M.W. Griffioen — Wed, 28 Sep 2022 15:10:06 +0000

After I installed the homing switches for X and Y on the E3D toolchanger, I finally had a decent starting point to get the tools pickup and parking tuned. Originally, I used sensorless homing but this caused changing offset values of the X- and Y positions of the machine. So the tools could not be …

Continue reading "E3D toolchanger: Tuning the tool pickups with reprap global variables and macro’s assistance"

Het bericht E3D toolchanger: Tuning the tool pickups with reprap global variables and macro’s assistance verscheen eerst op Jantec.nl.

E3D toolchanger upgrade: X-and Y- axis homing switches installing and configuring

J.M.W. Griffioen — Wed, 28 Sep 2022 15:02:19 +0000

My E3D toolchanger appeared to have some small inconsistencies in homing X and Y. This became apparant after I tried to tune the exact positions of the tools pickup, after having homed. Every time it was tuned, it worked well and the next day it was just a bit off. Then I retuned it again, …

Continue reading "E3D toolchanger upgrade: X-and Y- axis homing switches installing and configuring"

Het bericht E3D toolchanger upgrade: X-and Y- axis homing switches installing and configuring verscheen eerst op Jantec.nl.

Toolhead stepper fault and solution

Jan Griffioen — Sun, 28 Aug 2022 20:22:41 +0000

The toolhead stepper of my E3D toolchanger system suddenly broke down. The cause was a failed tool pickup move, due to which the rotating axle of the toolhead pickup system got blocked. After exchanging the stepper I changed the Duet’s settings so the C-drive will not be able to generate too much torque. This will …

Continue reading "Toolhead stepper fault and solution"

Het bericht Toolhead stepper fault and solution verscheen eerst op Jantec.nl.

E3D toolchanger Hymera fans 2, 4, 6 and 8 intermittent problem solved

Jan Griffioen — Fri, 26 Aug 2022 13:24:57 +0000

In the end, the solution to my intermittent on/off problem with my toolfans on the Hymera direct drives was extremely simple. The picture shows the solution, as the Hymera stepper driver obviously interferes with the 40mm fans. The problem was that these fans 2,4,6 and 8 not always started spinning. I tried to exchange the …

Continue reading "E3D toolchanger Hymera fans 2, 4, 6 and 8 intermittent problem solved"

Het bericht E3D toolchanger Hymera fans 2, 4, 6 and 8 intermittent problem solved verscheen eerst op Jantec.nl.

E3D 4-toolchanger 3D printer updates

Jan Griffioen — Tue, 19 Jul 2022 15:11:14 +0000

A big difference, the original object fan duct layout and the upgraded fan duct for the Hymera Direct Drive extruder/hotend combination!

Het bericht E3D 4-toolchanger 3D printer updates verscheen eerst op Jantec.nl.

Custom E3D toolchanger Dock adapter plate

Jan Griffioen — Sat, 16 Jul 2022 12:28:13 +0000

Jantec.nl E3D toolchanger Hymera DD DOCK adapter and 3mm shifted adapter download Tool T2 and T3 (3rd and 4th from left) are about 1.5 mm apart in the standard build, which means that T2’s tool fan can draw almost no air. With the new custom adapter, the right tool T3 moves 3 mm to the …

Continue reading "Custom E3D toolchanger Dock adapter plate"

Het bericht Custom E3D toolchanger Dock adapter plate verscheen eerst op Jantec.nl.

Calibrating E3D coreXY 4-toolchanger 3d printer

Jan Griffioen — Thu, 14 Jul 2022 20:28:08 +0000

I am in the process of calibrating the tools, the overall settings and so on so I can move on with the rest of the tools. In doing so, I always set all tools to settings that are in comparison to the first tool, T0. This way, should anything change, I have a solid reference. …

Continue reading "Calibrating E3D coreXY 4-toolchanger 3d printer"

Het bericht Calibrating E3D coreXY 4-toolchanger 3d printer verscheen eerst op Jantec.nl.

Building E3D coreXY 4-toolchanger 3d printer

Jan Griffioen — Tue, 28 Jun 2022 18:44:27 +0000

MORE E3D TOOLCHANGER POSTS 4xHemera direct drive first prints Tuning the tool pickups with reprap global variables X-and Y- axis homing switches installing and configuring Hymera fans 2, 4, 6 and 8 intermittent problem solved E3D 4-toolchanger 3D printer updates Custom E3D toolchanger Dock adapter plate Calibrating E3D coreXY 4-toolchanger 3d printer multicolor gadget …

Continue reading "Building E3D coreXY 4-toolchanger 3d printer"

Het bericht Building E3D coreXY 4-toolchanger 3d printer verscheen eerst op Jantec.nl.